30
sys admin>>NETWORK /ALL
Enter accepts present value
N-B: Enter IP address | 000.000.000.000>
N-B: Enter Subnet Mask | 255.255.255.255>
N-B: Enter Default Gateway address | 255.255.255.255>
N-B: Enter 2nd Dest. Network | 255.255.255.255>
N-B: Enter 2nd Netmask | 255.255.255.255>
N-B: Enter 2nd Gateway address | 255.255.255.255>
N-B: BOOTP at startup? | Y>
Save changes and update card? Yes or No: No>
N-C: Enter IP address | 000.000.000.000> 172.16.1.2
N-C: Enter Subnet Mask | 255.255.255.255> 255.255.255.0
N-C: Enter Default Gateway address | 255.255.255.255> 172.16.1.200
N-C: Enter 2nd Dest. Network | 255.255.255.255>
N-C: Enter 2nd Netmask | 255.255.255.255>
N-C: Enter 2nd Gateway address | 255.255.255.255>
N-C: BOOTP at startup? | Y>
Save changes and update card? Yes or No: No>y
Card installed, settings updated
N-D: Enter IP address | 000.000.000.000> 172.16.1.3
N-D: Enter Subnet Mask | 255.255.255.255> 255.255.255.0
N-D: Enter Default Gateway address | 255.255.255.255> 172.16.1.200
N-D: Enter 2nd Dest. Network | 255.255.255.255>
N-D: Enter 2nd Netmask | 255.255.255.255>
N-D: Enter 2nd Gateway address | 255.255.255.255>
N-D: BOOTP at startup? | Y>
Save changes and update card? Yes or No: No>y
Network card not installed in slot D
N-E: Enter IP address | 000.000.000.000> 172.16.1.4
N-E: Enter Subnet Mask | 255.255.255.255> 255.255.255.0
N-E: Enter Default Gateway address | 255.255.255.255> 172.16.1.200
N-E: Enter 2nd Dest. Network | 255.255.255.255>
N-E: Enter 2nd Netmask | 255.255.255.255>
N-E: Enter 2nd Gateway address | 255.255.255.255>
N-E: BOOTP at startup? | Y>
Save changes and update card? Yes or No: No>y
Network card not installed in slot E
sys admin>>
When used with the /ALL qualifier, the NETWORK command will allow the system
administrator to change the network parameters for all the card slots in order. The sys
admin will be prompted to enter the IP address, subnet mask, default gateway,
secondary route, and bootp settings for each card slot. If <ENTER> is pressed at the
prompt, the value displayed in the prompt will be used. After entering the parameters
for each slot, the sys admin will be asked if the new parameters should be used. If NO
is entered (or just <ENTER> is pressed), then the previously entered changes will be
discarded and the system will move on to the next slot’s parameters. If YES is entered,
then the slot’s network parameters will update in control card memory and the control
card will send the new parameters immediately to the card in that slot. If the card is a
network card, it will immediately acquire the new network parameters and disconnect all
telnet sessions to that card. If a terminal card is in the slot, or if the slot is empty, the
network parameter update is refused, but the network parameters for that slot will be
saved to control card memory.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals